![Schlage Schlage](/uploads/1/2/6/6/126662311/638555176.jpg)
Schlage Handpunch 2000 Xl Manual
HandPunch 3000 Manual.pdf HandPunch 3000 HandPunch Guys LLC 672 Dogwood Ave., Ste 223A Franklin Square, NY 11010 516-414-1290 HP-3000/4000 Terminal User's Guide This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of. The Schlage Biometric HandPunch 3000E hand scanner is equipped with hand geometry technology. Every time the employee places their hand into the HandPunch 3000E terminal, the camera takes a three dimensional scan of the length, width and height. It then turns the image into an algorithm and saves it for future verification. Drivers license test online spanish. The Schlage Biometric HandPunch 3000 is equipped with Hand Geometry Technology. Every time the employee places their hand into the HandPunch 3000 terminal, the camera takes a 3 dimensional scan of the length, width and height. It then turns the image into an algorithm and saves it for future verification. Jun 26, 2012 HandPunch 3000/4000 Manual There are two standard methods for providing earth grounding to HandPunch units:. earth grounding all units (see Figure 2-3). carrying an earth ground to each unit (see Figure 2-4) Earth ground all units when there is a good earth ground source near each unit and/or when there are very long cable runs between units. HandPunch 3000/4000 Installation Manual Revision 1.01 7 Additional Wiring HandPunch can control external devices: Bell Door Lock Request for Exit Switch Door Switch Auxiliary Devices Printer Wiring for these devices should enter the reader through the opening in the center of the wall plate or through conduit opening at the right side of the terminal. HandPunch 3000. Collects in and out times, with optional department entries. The 3000 series communicates with the host PC via serial, modem, RS485 or TCP/IP. Each HandPunch terminal comes with a short silver cable to connect the terminal to the network jack. Modem units include a black modem cable to connect the terminal to a.
Report gets its data from, to view data with the report. D If you want to create a new report or modify an existing report that does not have the data saved with it. Step 1: Create A Connection To The Data Source There are several types of data sources that you can use in Crystal Reports. Figure 2-20 shows the. SAP Crystal Reports application provides the facility for generating and designing the reports that customers needs.This tutorial about SAP Crystal Reports contains. Advantages of SAP Crystal Reports Sample Report; PDF training materials. Crystal reports 11 tutorial pdf. Crystal Reports Tutorial in PDF - You can download the PDF of this wonderful tutorial by paying a nominal price of $9.99. Your contribution will go a long way in. In the Creating Custom Crystal Reports Tutorial. In a PDF, page numbers in the Table of Contents, Index, and all cross-references are hyperlinks. For example, click the page number by any. Accept the defaults for all other fields on the General tab.
Handpunch 3000 User Manual
![Manual Manual](https://d2ydh70d4b5xgv.cloudfront.net/images/6/8/ingersoll-rand-recognition-systems-handpunch-1000-e-hp-1000-scanner-time-clock-b34b243b167cfbfe99064913b5b1ca49.jpg)
Schlage Hp 3000 Manual
- 3Table of Contents
- 5Introduction
- 6Biometrics
- 6Principle of Operation
- 9Specifications
- 13Planning an Installation
- 13Site Preparation
- 13HandPunch Placement
- 14Wiring
- 14Power Input
- 14Battery Backup
- 15Earth Ground and Shielding
- 20Communications
- 22External Devices
- 25Mechanical Installation
- 25Wall Plate Installation
- 26Mounting the Wall Plate
- 29Networking and Communications
- 29Stand-alone HandReader
- 29Master or Remote HandReader in a HandReader Network
- 29Remote HandReader in a HandReader Network Connected to a Host PC
- 30Remote HandReader Connected to a Host PC Via Optional Modem
- 31Remote HandReader Connected to a Host PC Via Optional Ethernet
- 31Printer
- 33Wiring Connections
- 45Erasing the Memory
- 47Closing the HandPunch
- 49Enter Command Menu
- 49If No One Is Enrolled in the HandPunch
- 49If Users Are Enrolled in the HandPunch
- 51Navigating Command Menus
- 53Programming the HandPunch
- 54Programming Order
- 55System Management
- 56Service Menu
- 58Setup Menu
- 62Management Menu
- 65Enrollment Menu
- 69Special Menu
- 71HandPunch Maintenance
- 72Appendix A - Installation Tips
- 80Wiring Examples
- 93Setting the Dip Switches
- 94Communication Method
- 94Erasing Handpunch Memory
- 96Appendix D - Troubleshooting
- 98Glossary
- 100Limited Warranty